[vpn-help] Setup with a Netgear FSV318v3

[Rick Utter]

I am currently having a problem getting phase 2 to connect to my netgear FSV318v3.  I can connect successfully with Netgear's client, so I know that the firewall on the server side is allowing traffic through, but I get in the logs:

.......

10/08/22 11:27:52 ii : phase1 sa established
0/08/22 11:27:52 ii : ***.***.***.***:500 <-> 192.168.100.107:500
10/08/22 11:27:52 ii : 4414145352353:235112355eb4423
10/08/22 11:27:52 ii : sending peer INITIAL-CONTACT notification
10/08/22 11:27:52 ii : - 192.168.100.107:500 -> ***.***.***.***:500
10/08/22 11:27:52 ii : - isakmp spi = 85775b003b4f664e:600538a5294ce238
10/08/22 11:27:52 ii : - data size 0
10/08/22 11:27:52 >> : hash payload
10/08/22 11:27:52 >> : notification payload
10/08/22 11:27:52 == : new informational hash ( 20 bytes )
10/08/22 11:27:52 == : new informational iv ( 8 bytes )
10/08/22 11:27:52 >= : cookies 85775b003b4f664e:600538a5294ce238
10/08/22 11:27:52 >= : message b01cbdae
10/08/22 11:27:52 >= : encrypt iv ( 8 bytes )
10/08/22 11:27:52 == : encrypt packet ( 80 bytes )
10/08/22 11:27:52 == : stored iv ( 8 bytes )
10/08/22 11:27:52 -> : send NAT-T:IKE packet 192.168.100.107:500 -> ***.***.***.***:500 ( 112 bytes )
10/08/22 11:27:52 DB : config added ( obj count = 1 )
10/08/22 11:27:52 ii : building config attribute list
10/08/22 11:27:52 ii : - IP4 Address
10/08/22 11:27:52 ii : - Address Expiry
10/08/22 11:27:52 ii : - IP4 Netamask
10/08/22 11:27:52 ii : - IP4 WINS Server
10/08/22 11:27:52 == : new config iv ( 8 bytes )
10/08/22 11:27:52 ii : sending config pull request
10/08/22 11:27:52 >> : hash payload
10/08/22 11:27:52 >> : attribute payload
10/08/22 11:27:52 == : new configure hash ( 20 bytes )
10/08/22 11:27:52 >= : cookies 853215123512349813ebc8
10/08/22 11:27:52 >= : message 552bae5b
10/08/22 11:27:52 >= : encrypt iv ( 8 bytes )
10/08/22 11:27:52 == : encrypt packet ( 76 bytes )
10/08/22 11:27:52 == : stored iv ( 8 bytes )
10/08/22 11:27:52 -> : send NAT-T:IKE packet 192.168.100.107:500 -> ***.***.***.***:500 ( 104 bytes )
10/08/22 11:27:52 DB : config resend event scheduled ( ref count = 2 )
10/08/22 11:27:52 DB : phase2 not found
10/08/22 11:27:57 -> : resend 1 config packet(s) 192.168.100.107:500 ->  ***.***.***.***:500
10/08/22 11:28:02 -> : resend 1 config packet(s) 192.168.100.107:500 ->  ***.***.***.***:500
10/08/22 11:28:07 -> : resend 1 config packet(s) 192.168.100.107:500 ->  ***.***.***.***:500
10/08/22 11:28:07 DB : phase1 found
10/08/22 11:28:07 -> : send NAT-T:KEEP-ALIVE packet 192.168.100.107:500 ->  ***.***.***.***:500
10/08/22 11:28:12 ii : resend limit exceeded for config exchange
10/08/22 11:28:12 DB : config deleted ( obj count = 0 )


.....

After this, all I get is NAT keepalives and then the closing entries when I finally cancel.   It does not seem to time out (or at least not in the 10 minutes that I let it sit to see if it would).  

Software: Windows XP 32 bit and Windows 7 64 bit (both doing exactly the same thing).
Hardware: Netgear FVS318v3 with the latest firmware code (3.0 r 28)

Any thoughts?  Thanks a lot!
 		 	   		  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.shrew.net/pipermail/vpn-help/attachments/20100822/7f0a5aa3/attachment-0001.html>