[vpn-help] Funkwerk R4100 crashes on Phase2 totally

[Andreas]

Zitat von Dirk Wahrheit <wahrheit at macnetix.de>:

> Hi,
>
> I am using a Funkwerk (Former Bintec) R4100 with latest SW-Release  
> V.7.9 Rev. 5 (Patch 5) IPSec from 2011/02/04 00:00:00
> When I connect with the Shewsoft Client V.2.1.7 the Router crashes  
> totally and reboots.
> Connections from Old Bintec IPSec Client and NCP Client are fine.
>
> Settings for Shewsoft Client from (german with English screenshots):
> http://www.router-forum.de/board-bintec-funkwerk-enterprise-communications/thread-ipsec-bintec--lt---gt--shrew-soft-client-51944-page-1.html
>
> Settings for R4100 as given in the Article (german):
> http://www.funkwerk-ec.com/faq_bintec_262_ipsecclient_zu_r3000_ikeconfigmode_fci_01_de,10993,194.html
>
>
> Any Ideas?
>
> debug log from Funkwerk R4100 console:
> 16:45:31 DEBUG/IPSEC: P1: peer 0 () sa 3 (R): new ip 79.197.214.162  
> <- ip 178.26.9.170
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is 'draft-ietf-ipsec-nat-t-ike-00'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is '16f6ca16e4a4066d83821a0f0aeaa862'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is 'draft-ietf-ipsec-nat-t-ike-02'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is 'draft-ietf-ipsec-nat-t-ike-03'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is '4a131c81070358455c5728f20e95452f'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is '4048b7d56ebce88525e7de7f00d6c2d380000000'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is 'Dead Peer Detection (DPD, RFC 3706)'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is 'f14b94b7bff1fef02773b8c49feded26'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is '166f932d55eb64d8e4df4fd37e2313f0d0fd8451'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is '8404adf9cda05760b2ca292e4bff537b'
> 16:45:31 INFO/IPSEC: P1: peer 0 () sa 3 (R): Vendor ID:  
> 178.26.9.170:500 (No Id) is '12f5f28c457168a9702d9fe274cc0100'
> 16:45:31 DEBUG/IPSEC: P1: peer 3 (MAC_Schwanke-Seer) sa 3 (R):  
> identified ip 79.197.214.162 <- ip 178.26.9.170
> 16:45:31 DEBUG/INET: NAT: new incoming session on ifc 10001 prot 17  
> 79.197.214.162:4500/79.197.214.162:4500 <- 178.26.9.170:4500
>
> è Here Router crashes and reboots

Contact Funkwerk Support. Nothing ever sent by a VPN client should  
crash the VPN router. We have a BinTEC VPN-25 and no problem with  
Shrewsoft VPN clients.

Regards